UP Power Corporation Limited conducts a recruitment campaign for Junior Engineers. The recruitment process is often divided into two phases: written test and document verification. The same can be expected during the 2024 examination cycle. Aspirants preparing for the UPPCL JE Recruitment process should thoroughly review the UPPCL JE Syllabus 2024. The exam consists of four sections: technical knowledge, general awareness, logical reasoning, and general Hindi. Going through the UPPCL JE Syllabus 2024 will help you determine the topics that are vital for the exam and demand more time to prepare than others. Examine the UPPCL JE Syllabus 2024 carefully.
Click here for the official website.
UPPCL JE Syllabus 2024
UP Power Corporation Limited conducts a recruitment campaign for Junior Engineers. The recruitment process is often divided into two phases: written test and document verification. The same can be expected during the 2024 examination cycle. Aspirants preparing for the UPPCL JE Recruitment process should thoroughly review the UPPCL JE Syllabus 2024. The exam consists of four sections: technical knowledge, general awareness, logical reasoning, and general Hindi. Going through the UPPCL JE Syllabus 2024 will help you determine the topics that are vital for the exam and demand more time to prepare than others. Examine the UPPCL JE Syllabus 2024 carefully.
UPPCL JE Syllabus for Electrical Engineering
Subject | Topic |
Digital Electronics | Bridges and Potentiometers |
Measurement of voltage, current, power, energy and power factor | |
Instrument transformers | |
Digital voltmeters and multimeters | |
Phase, Time and Frequency measurement | |
Oscilloscopes | |
Error analysis | |
Electrical Machines | Single-phase transformer: equivalent circuit, phasor diagram, open circuit, and short circuit tests, regulation, and efficiency |
Three-phase transformers: connections, vector groups, parallel operation | |
Auto-transformer | |
Electromechanical energy conversion principles | |
DC machines: separately excited, series and shunt, motoring and generating, mode of operation and their characteristics, speed control of DC motors | |
Three-phase induction machines: the principle of operation, types, performance, torque-speed characteristics, no-load and blocked-rotor tests, equivalent circuit, starting and speed control | |
Operating principle of single-phase induction motors | |
Synchronous machines: cylindrical and salient-pole machines, performance and characteristics, regulation and parallel operation of generators, starting of synchronous motors | |
Types of losses and efficiency calculations of electric machines | |
Digital Signal Processing | – |
Measurements, Instrumentation, and Transducers | – |
Analytical Instrumentation | – |
Power Electronics | Static V-I characteristics and firing/gating circuits for Thyristor, MOSFET, IGBT |
DC to DC conversion: Buck, Boost and Buck-Boost Converters | |
Single and three-phase configuration of uncontrolled rectifiers | |
Voltage and Current commutated Thyristor based converters | |
Bidirectional AC to DC voltage source converters | |
Magnitude and Phase of line current harmonics for uncontrolled and thyristor based converters | |
Power factor and Distortion Factor of AC to DC converters | |
Single-phase and three-phase voltage and current source inverters, sinusoidal pulse width modulation | |
Electrical Circuits and Fields | Network elements: ideal voltage and current sources, dependent sources, R, L, C, M elements |
Network solution methods: KCL, KVL, Node, and Mesh analysis | |
Network Theorems: Thevenin’s, Norton’s, Superposition and Maximum Power Transfer theorem | |
Transient response of DC and AC networks, sinusoidal steady-state analysis, resonance, two-port networks, balanced three-phase circuits, star-delta transformation, complex power and power factor in AC circuits | |
Coulomb’s Law, Electric Field Intensity, Electric Flux Density, Gauss’s Law, Divergence, Electric field and potential due to point, line, plane and spherical charge distributions | |
Effect of dielectric medium, Capacitance of simple configurations | |
Biot-Savart’s law, Ampere’s law, Curl, Faraday’s law, Lorentz force, Inductance, Magnetomotive force, Reluctance, Magnetic circuits, Self and Mutual inductance of simple configurations | |
Control Systems | Mathematical modeling and representation of systems |
Feedback principle | |
Transfer function | |
Block diagrams and Signal flow graphs | |
Transient and Steady-state analysis of linear time invariant systems | |
Stability analysis using Routh-Hurwitz and Nyquist criteria | |
Bode plots | |
Root loci | |
Lag, Lead and Lead-Lag compensators | |
P, PI and PID controllers | |
State space model, Solution of state equations of LTI systems | |
Industrial Instrumentation | – |
Computer Control of Processes, Networks | – |
Communication Engineering | – |
Power Electronics and Drives | – |
Power Systems | Basic concepts of electrical power generation |
AC and DC transmission concepts | |
Models and performance of transmission lines and cables | |
Economic Load Dispatch (with and without considering transmission losses) | |
Series and shunt compensation | |
Electric field distribution and insulators | |
Distribution systems | |
Per-unit quantities | |
Bus admittance matrix | |
Gauss-Seidel and Newton-Raphson load flow methods | |
Voltage and Frequency control | |
Power factor correction | |
Symmetrical components | |
Symmetrical and unsymmetrical fault analysis | |
Principles of over-current, differential, directional and distance protection | |
Circuit breakers | |
System stability concepts | |
Equal area criterion |
UPPCL JE Syllabus for Civil Engineering
Subject | Topic |
Building Materials | Physical and Chemical properties, classification, standard tests, uses and manufacture/quarrying of materials (e.g., building stones, silicate-based materials, cement (Portland), asbestos products, timber and wood-based products, laminates, bituminous materials, paints, varnishes). |
Estimating, Costing and Valuation | Estimate, glossary of technical terms, analysis of rates, methods and unit of measurement, items of work – earthwork, brick work (Modular & Traditional bricks), RCC work, shuttering, timber work, painting, flooring, plastering. Boundary wall, brick building, water tank, septic tank, bar bending schedule, center line method, midsection formula, trapezoidal formula, Simpson’s rule. Cost estimate of septic tank, flexible pavements, tube well, isolated and combined footings, steel truss, piles and pile-caps. Valuation – value and cost, scrap value, salvage value, assessed value, sinking fund, depreciation and obsolescence, methods of valuation. |
Surveying | Principles of surveying, measurement of distance, chain surveying, working of prismatic compass, compass traversing, bearings, local attraction, plane table surveying, theodolite traversing, adjustment of theodolite, leveling, definition of terms used in leveling, contouring, curvature and refraction corrections, temporary and permanent adjustments of dumpy level, methods of contouring, uses of contour map, tachometric survey, curve setting, earth work calculation, advanced surveying equipment. |
Soil Mechanics | Origin of soil, phase diagram, definitions-void ratio, porosity, degree of saturation, water content, specific gravity of soil grains, unit weights, density index and interrelationship of different parameters, grain size distribution curves, and their uses. Index properties of soils, Atterberg’s limits, ISI soil classification, and plasticity chart. Permeability of soil, coefficient of permeability, determination of coefficient of permeability, unconfined and confined aquifers, effective stress, quick sand, consolidation of soils, principles of consolidation, degree of consolidation, preconsolidation pressure, normally consolidated soil, e-log p curve, computation of ultimate settlement. Shear strength of soils, direct shear test, vane shear test, triaxial test. Soil compaction, laboratory compaction test, maximum dry density and optimum moisture content, earth pressure theories, active and passive earth pressures, bearing capacity of soils, plate load test, standard penetration test. |
Hydraulics | Fluid properties, hydrostatics, measurements of flow, Bernoulli’s theorem and its application, flow through pipes, flow in open channels, weirs, flumes, spillways, pumps and turbines. |
Irrigation Engineering | Definition, necessity, benefits, effects of irrigation, types and methods of irrigation, hydrology – measurement of rainfall, runoff coefficient, rain gauge, losses from precipitation – evaporation, infiltration, etc. Water requirement of crops, duty, delta and base period, Kharif and Rabi crops, command area, time factor, crop ratio, overlap allowance, irrigation efficiencies. Different types of canals, types of canal irrigation, loss of water in canals. |
Canal Lining | Types and advantages. Shallow and deep wells, yield from a well. Weir and barrage, failure of weirs and permeable foundation, slit and scour, Kennedy’s theory of critical velocity, Lacey’s theory of uniform flow. Definition of flood, causes and effects, methods of flood control, water logging, preventive measures. Land reclamation, characteristics affecting fertility of soils, purposes, methods, description of land and reclamation processes. Major irrigation projects in India. |
Transportation Engineering | Highway Engineering – cross sectional elements, geometric design, types of pavements, pavement materials – aggregates and bitumen, different tests, design of flexible and rigid pavements – Water Bound Macadam (WBM) and Wet Mix Macadam (WMM), gravel road, bituminous construction, rigid pavement joint, pavement maintenance, highway drainage. Railway Engineering – components of permanent way – sleepers, ballast, fixtures, and fastening, track geometry, points and crossings, track junction, stations and yards. Traffic Engineering – different traffic surveys, speed-flow-density, and their interrelationships, intersections, and interchanges, traffic signals, traffic operation, traffic signs and markings, and road safety. |
Environmental Engineering | Quality of water, source of water supply, purification of water, distribution of water, need of sanitation, sewerage systems, circular sewer, oval sewer, sewer appurtenances, sewage treatments. Surface water drainage. Solid waste management – types, effects, engineered management system. Air pollution – pollutants, causes, effects, control. Noise pollution – cause, health effects, control. |
Structural Engineering | Theory of structures: Elasticity constants, types of beams – determinate and indeterminate, bending moment and shear force diagrams of simply supported, cantilever, and overhanging beams. Moment of area and moment of inertia for rectangular & circular sections, bending moment and shear stress for tee, channel, and compound sections, chimneys, dams and retaining walls, eccentric loads, slope deflection of simply supported and cantilever beams, critical load and columns, torsion of circular section. |
Concrete Technology | Properties, advantages, and uses of concrete, cement aggregates, importance of water quality, water cement ratio, workability, mix design, storage, batching, mixing, placement, compaction, finishing and curing of concrete, quality control of concrete, hot weather and cold weather concreting, repair and maintenance of concrete structures. |
RCC Design | RCC beams – flexural strength, shear strength, bond strength, design of singly reinforced and doubly reinforced beams, cantilever beams. T-beams, lintels. One way and two way slabs, isolated footings. Reinforced brick works, columns, staircases, retaining wall, water tanks (RCC design questions may be based on both Limit State and Working Stress methods). |
Steel Design | Steel design and construction of steel columns, beams, roof trusses, plate girders. |
UPPCL JE Syllabus for General Awareness/ Knowledge
Topics for General Awareness/ Knowledge covered in UPPCL JE Syllabus | |
Indian History | Events related to India and its neighboring countries |
Indian Constitution | General Polity |
Indian Economy | Indian Culture & Heritage |
Current Affairs – International & National | Science & Technology |
Indian & World Geography |
UPPCL JE Syllabus for Reasoning
Topics for Reasoning covered in UPPCL JE Syllabus | |
Series Completion | Statement – Conclusions |
Alpha-Numeric Sequence Puzzle | Direction Sense Test |
Number, Ranking & Time Sequence | Logical Venn Diagrams |
Clocks & Calendars | Deriving Conclusions from Passages |
Situation Reaction Test | Alphabet Test |
Statement – Arguments | Eligibility Test |
Classification | Data Sufficiency |
Coding-Decoding | Theme Detection |
Arithmetical Reasoning | Logic |
Mathematical Operations | Analogy |
Inserting The Missing Character | Puzzle Test |
Logical Sequence of Words |
UPPCL JE Syllabus for General Hindi
Topics for General Hindi covered in UPPCL JE Syllabus | |
Phrases | Plural Forms |
Translation of Sentences | Comprehension |
Fill in the Blanks | Synonyms |
Grammar | Antonyms |
Vocabulary | Error Detection |
UPPCL JE Exam Pattern 2024
The UPPCL JE Exam Pattern has four key subjects: Technical Syllabus, General Awareness, Reasoning, and General Hindi. This written examination will include 200 objective-type questions worth a total of 200 points. The examination will take three hours. The table below gives details about the UPPCL JE complete Exam Pattern 2024. The UPPCL JE Exam Pattern 2024 is predicted to remain the same. The adjustments to the 2024 exam cycle are scheduled to be announced in an official statement.
Subject Names | Questions | Marks | Exam Duration |
Technical Syllabus | 150 | 150 | 3 hrs |
General Awareness | 20 | 20 | |
Reasoning | 20 | 20 | |
General Hindi | 10 | 10 | |
Total | 200 | 200 |
Check here for more information-
Hopefully, this information was useful for all the aspiring candidates preparing for the government exams. Check DailyExamNews to stay informed about the latest recruitments, tests, vacancies, and developments regarding government exams.